The operating instructions mentioned here are partial abstracts SECTION 1
from the Operating Instruction Manual. The page numbers of
the Operating Instruction Manual remain as in the manual.GENERAL
Getting StartedGetting startedGetting StartedGetting Started
Warning on power connection
PrecautionsIdentifying Parts and Controls
Y Use an appropriate power cord for your local powerSee the pages in parentheses for further details.
Installationsupply.
FrontRear
Y Prevent internal heat build-up by allowing adequate airExamples of plug types
circulation. Do not place the monitor on surfaces (rugs,
blankets, etc.) or near materials (curtains, draperies) that
may block the ventilation holes.
(HD15)
Y Do not install the monitor near heat sources such as(13W3)
radiators or air ducts, or in a place subject to directfor 100 to 120 V ACfor 200 to 240 V ACfor 240 V AC only
sunlight, excessive dust, mechanical vibration or shock.
Y Do not place the monitor near equipment which generatesY Before disconnecting the power cord, wait at least 30
magnetism, such as a transformer or high voltage powerseconds after turning off the power to allow the static
lines.electricity on the CRT display surface to discharge.
Y After the power has been turned on, the CRT is
demagnetized (degaussed) for about 3 seconds. This
Maintenancegenerates a strong magnetic field around the metal frame,
which may affect the data stored on magnetic tapes and
Y Clean the cabinet, panel and controls with a soft clothdisks near the bezel. Place magnetic recording equipment,
lightly moistened with a mild detergent solution. Do nottapes and disks away from this monitor.
use any type of abrasive pad, scouring powder or solvent,
1-1such as alcohol or benzine.The outlet should be installed near the equipment1 ? (reset) button (page 14)7 AC IN connector
Y Do not rub, touch, or tap the surface of the screen withand be easily accessible.Resets the adjustments to the factory settings.ENProvides AC power to the monitor.
sharp or abrasive items such as a ballpoint pen or
screwdriver. This type of contact may result in a scratched2 (auto sizing and centering) button8 Video input 1 connector (HD15)F
picture tube.(page 5)Inputs RGB video signals (0.700 Vp-p, positive) and
Automatically adjusts the size and centering of theSYNC signals.ES
images.
Transportation5 4 3 2 1
3 ? (brightness) (./>) buttons (pages 5 �C
14)10 9 8 7 6
When you transport this monitor for repair or shipment, useAdjust the picture brightness.15 14 13 12 11
the original carton and packing materials.
Function as the (./>) buttons when adjusting other
items.Pin No.SignalPin No.Signal
Use of the Tilt-Swivel1Red8Blue Ground
4 (menu) button (pages 5 � 14)9DDC + 5V*
2Green
With the tilt-swivel, this monitor can be adjusted to theDisplays the MENU OSD.(Composite10Ground
desired angle within 180! horizontally and 20! vertically.Sync on Green)
5 > (contrast) (?//) buttons (pages 5 � 14,
To turn the monitor vertically and horizontally, hold it at11ID (Ground)
the bottom with both hands as illustrated below.18)3Blue12Bi-Directional
Adjust the contrast.4ID (Ground)Data (SDA)*
Function as the (?//) buttons when adjusting other5DDC Ground*13H. Sync
15°
items.
90°6Red Ground14V. Sync
6 u (power) switch and indicator (pages 15,7Green Ground15Data Clock(SCL)*
90°18)* Display Data Channel (DDC) Standard of VESA
Turns the monitor on or off.
5°
The indicator lights up in green when the monitor is(continued)
turned on, and lights up in orange when the monitor is
in power saving mode.
23 |